Interior sandblasting line and application of thermoplastic layer

Descriere

Model Rotoblast 3H-120 & RotoCoat 2H
ID UC01
Status Active
Pret 33.000 € + TVA
An fabricatie 2011
Carburant Electric
Locatie Romania
Fisiere TS Rotoblast 3H_ENG (1).pdf
TS Rotocoat 2H_ENG.pdf

Interior sandblasting line and application of thermoplastic layer

 

This line has:

1. Filter with welded pressure vessel: DANTHERM FILTRATION 5230-SC034-SQ200, year 2011, serial no. 8502711 and MJC 9/22/2-2 welded pressure vessel, year 2011, serial no. 118001730

2. Abrasive blasting machine, hodge clemco Ltd, model 2462, year 2011, serial no. 7758

3. The main machine a Rotoblast 3H-120, year 2011, serial no. 11002

4. The second machine is a RotoCoat 2H, year 2011

____________________

ROTOBLAST 3H

DESCRIPTION

The Rotoblast 3H consists of a carousel conveyor with 3 stations where the cylinders rotate during grit-blasting and air blowing operations.

The equipment features 3 separate lances with specific blasting nozzles for blasting the cylinder top, body and bottom.

The operating cycle consists of 4 phases (3 grit-blasting phases + 1 air blowing phase), followed by an additional dust and grit extraction phase off-line.

Estimated productivity: about 40 to 50 pcs/hour, depending on the cylinder length and steel condition.

Recommended abrasive grade: Steel Grit (G40 mesh size) for M30 cylinders.

The whole working cycle is controlled by a programmable PLC allowing the operator to program and set the following values:

Lance speed up and down, individually adjustable for each single lance, thus ensuring maximum blasting flexibility (i.e. each lance can have a different up movement speed, down movement speed a n d  i n t e r m e d i a t e  p a u s e s  c a n  b e programmed)

Cycle time

A virtually unlimited number of programmable programs for different cylinder types (cylinder length, number of welds, type of ring-nuts etc…)

Operations to be carried out by the operator:

Positioning the cylinders inside the cabinet

Starting the automatic grit-blasting cycle

Unloading the inner-blasted cylinders

 Pause time for additional blasting at the ring-nut position (particularly useful for example for M74 ring-nuts) and at the welds

Electric power rating:

Voltage: 380 V

Compressed air supply:

Volume of dry: 20,000 Litres/min

Compressed air: 700 Cfm

Machine dimensions: Width: = 2500 mm Depth:=2500 mm Height:=2500 Mm

RotoCoat 2H 

Automatic Inner Rotational Lining Equipment for Fire Extinguisher Cylinders for lining cylinders with EN3 approved Corrosion Resistant Thermoplastic Coating powders.

RotoCoat 2H has been designed to apply a thermoplastic protective lining, to carbon steel fire extinguisher cylinders. The equipment is supplied ready for use and only requires connection to the mains services on site.

General Description

The machine consists of a sturdy fabricated steel structure mounted on 4 adjustable levelling feet. The machine main rotation beam on which the machine body is installed is mounted on two bearings fixed to each side of the support frame, allowing machine body rotation up to 180°.The fire-extinguisher cylinders are mounted on supports and fixed to said supports with special adaptors. These supports rotate around their axis to allow cylinder rotation. Cylinder rotation ensures homogeneous cylinder surface heating and, during the lining phase, allows even powder distribution inside the cylinders. Powder transfer is ensured via two powder containers which must be manually installed (with special quick releases) on the machine body on the opposite side to the cylinders before starting the cycle.

Pre-heating and powder melting are carried out by means of two burner systems installed on the rear part of the machine body.

Burner Systems: each burner system consists of one main side burner, one top burner and one bottom burner. The position of the burners can be changed according to the type of cylinder to coat, thus ensuring the best cylinder pre-heating conditions as it will be possible to adjust the heating capacity to the different types of cylinders.

  • Metal thickness;
  • Ring-nut type;
  • Dimensions

Machine parameter (processing parameter) management is done by a PLC.

Control Panel: the following time and speed settings are available on the control panel:

  • Pre-heat Time;
  • Lining Time;
  • Cure Time;
  • Cooling Time;
  • Total Cycle Time;
  • Cylinder Rotation Speed;
  • Cylinder Tilting Speed.

Any other data (piece count, troubleshooting etc.) can be programmed in the PLC Software.

Burner Control Units are placed on the side of the machine.

 

Price: 33.000 Euro + VAT, FCA Bucharest

Contact

Tel.: +40-359/175.575
Fax: +40-259/426.248
Mobil: +40-743/177.040 ; +40-740/221.698

Vizionarea produsului se programează cu 24 de ore înainte.

We speak English. Wir sprechen Deutsch. (+40-740/221.698 )
Hablamos Español. Beszélünk magyarul. (+40-743/177.040 )

Irrtum, Anderungen und Zwischenverkauf vorbehalten /
Subject to errors, changes and prior sale /
Ne rezervăm dreptul la greșeli, modificări și vânzare prealabilă.

Formular contact

Sunt de acord sa ma abonez la newsletter (vezi termeni si conditii)